MitoSOX Red is a fluorescent dye serving as a mitochondria-targeted fluorescent probe for superoxide, with cell membrane permeability and specificity. Upon oxidation, MitoSOX Red subsequently binds to nucleic acids within mitochondria/nuclei, producing intense red fluorescence, and is employed for detecting mitochondrial superoxide in live cells.

I. Solution Preparation
1. MitoSOX Red Stock Solution Preparation: Dissolve MitoSOX Red in DMSO, typically at a concentration of 1-10 mM, which can be optimized based on experimental conditions.
2. Working Solution Preparation: Dilute the MitoSOX Red stock solution to a concentration suitable for the experiment. The common final concentration range is 1 to 10 µM, but this should be optimized according to cell type and experimental conditions.
3. Control Reagents: Use superoxide dismutase (SOD) as a negative control, as SOD scavenges superoxide and prevents the oxidation of MitoSOX Red.

II. Cell Labeling
1. Cell Culture: Seed cells into appropriate culture vessels (such as culture dishes or coverslips) and culture for 24-48 hours until cells are fully attached and grown.
2. MitoSOX Red Staining: Add working concentration of MitoSOX Red to the culture medium. Incubate at 37°C for 10 to 30 minutes; staining time should be optimized according to cell type.
3. Washing: After incubation, thoroughly wash cells with PBS to remove excess MitoSOX Red.
4. Fluorescence Detection:
1) Excitation and Emission Wavelengths: The excitation wavelength of MitoSOX Red is 510 nm, and the emission wavelength is 580 nm. Use a fluorescence microscope or flow cytometer equipped with appropriate filters to detect red fluorescence.
2) Superoxide Detection: The intensity of red fluorescence is proportional to the superoxide level in mitochondria. Higher fluorescence intensity indicates higher superoxide levels, while low fluorescence indicates lower superoxide levels.
5. Experimental Controls:
1) Positive Control: Use known oxidative stress inducers, such as Paraquat or Rotenone, to elevate intracellular superoxide levels, thereby increasing MitoSOX Red fluorescence.
2) Negative Control: Add Mito-TEMPO to prevent superoxide from oxidizing MitoSOX Red, thereby reducing or eliminating fluorescence.
6. Quantitative Analysis:
For quantitative analysis, flow cytometry can be used to measure fluorescence intensity of individual cells, which helps analyze superoxide levels in large cell populations. Qualitative assessment can also be performed through image analysis.

I. Solution preparation
1. MitoSOX Red stock solution preparation: MitoSOX Red is dissolved in DMSO, usually at a concentration of 1-10mM, which can be optimized according to experimental conditions.
2. Working solution preparation: Dilute the MitoSOX Red stock solution to a concentration suitable for the experiment. Common final concentrations range from 1 to 10 µM, but should be optimized according to cell type and experimental conditions.
3. Control reagent: Use superoxide dismutase (SOD) as a negative control because SOD will scavenge superoxide and prevent oxidation of MitoSOX Red.
II. Cell labeling
1. Cultivate cells: Inoculate cells into appropriate culture vessels (such as culture dishes or coverslips) and culture for 24-48 hours until cells are fully attached and growing.
2. MitoSOX Red staining: Add the working concentration of MitoSOX Red to the culture medium. Incubate at 37°C for 10 to 30 minutes. Staining time should be optimized based on cell type.
3. Washing: After incubation, wash cells thoroughly with PBS to remove excess MitoSOX Red.
4. Fluorescence detection:
1) Excitation and emission wavelengths: MitoSOX Red has an excitation wavelength of 510 nm and an emission wavelength of 580 nm. Use a fluorescence microscope or flow cytometer equipped with appropriate filters to detect red fluorescence.
2) Superoxide detection: The intensity of red fluorescence is proportional to the level of superoxide in mitochondria. Higher fluorescence intensity indicates higher superoxide levels, while lower fluorescence indicates lower superoxide levels.
5. Experimental controls:
1) Positive control: Use known oxidative stress inducers, such as Paraquat or Rotenone, to elevate superoxide levels in cells, thereby increasing the fluorescence of MitoSOX Red.
2) Negative control: Add Mito-TEMPO to prevent superoxide from oxidizing MitoSOX Red, thereby reducing or eliminating fluorescence.
6. Quantitative analysis:
For quantitative analysis, flow cytometry can be used to measure the fluorescence intensity of individual cells, which helps to analyze superoxide levels in a large number of cells. Qualitative assessment can also be performed by image analysis.
Notes:
1. MitoSOX Red is light-sensitive, so it should be avoided from exposure to light during storage and operation.
2. This probe specifically targets mitochondria and will only be oxidized by superoxide, not other ROS or RNS, thus ensuring the specificity of the detection.
3. During the incubation process, ensure that the cells are not overly stressed or damaged to avoid causing artifacts or nonspecific fluorescence.

The above information is based on published literature. Experimental procedures should be appropriately modified to meet specific research demands.

DMSO: 101 mg/mL (132.95 mM), Sonication is recommended.

10% DMSO+40% PEG300+5% Tween-80+45% Saline: 3.3 mg/mL (4.34 mM), Sonication is recommended.